Publish Time: 2021-09-13 Origin: Site
Labeling machine mainly includes self-adhesive Labeling machine, sleeve Labeling machine, round bottle Labeling machine, beer Labeling machine, semi-automatic Labeling machine, automatic Labeling machine, hot melt adhesive self-adhesive Labeling machine. These Labeling machine products can be pasted on flat surfaces, single-sided or multi-sided pasting of packages, cylindrical pasting, partially or completely covered cylindrical pasting, concave and corner pasting, etc. If you want the Labeling machine to have a longer service life, then we take good care of the Labeling machine and pay attention to the maintenance of the Labeling machine. So how to maintain the Labeling machine? Let's take a look at it.
This is the content list:
Adjustment of the Labeling machine pressure brush mechanism
Adjusting the Labeling machine cassette
Adjustment of the Labeling machine inlet star wheel, outlet star wheel, and inlet screw
Adjustment of the Labeling machine standard station
The center of the Labeling machine marker is aligned with the label and is symmetrical on both sides, the Labeling machine brush is perpendicular to the container surface. Pressure brush sweep over the container overlap gap of single pressure brush for 10mm-15mm, while the combination of pressure brush for 5mm-10mm. distance between the cleaning brush and sponge is 1mm-2mm. adjust the pressure bottle head. When there is no bottle, the pressure head should be 20mm lower than when there is a bottle.
In the centerline of the Labeling machine label cassette, the center axis of the label station is tangent to label paper and the center axis of the label plate forms a line at three points. Adjust the tangent line (0 distance) between the Labeling machine label plate and the label paper, then move the label cassette closer by 1mm-2mm. The gap between the label paper in the Labeling machine label cassette and the pressure strip on both sides should be between 0.8mm and 1mm. If the gap is too large, the label paper will move in the label cassette and slash marks will appear. If the gap is too small, it will result in poor label push-in. Adjust the position of the Labeling machine label cassette gripping hooks so that the upper and lower, left and right gripping hooks are in the same vertical plane and work with even force on the label paper, so it can grip the label smoothly. The Labeling machine label supply rollers are adjusted so that when no labels are available, the label platen can be pressed against the front of the label cassette and the labels near the label hook fingers are not crushed.
When adjusting the Labeling machine inlet star wheel, outlet star wheel, and inlet screw, the Labeling machine pressure head should prevail. First, adjust the Labeling machine inlet star wheel. When the bottle pressure head just overwhelms the bottle, please adjust the bottle inlet star wheel so that the bottle is located in the middle of the star wheel groove. The adjustment of the bottle feed screw is based on the bottle feed star wheel. When the bottle is in the middle of the inlet star wheel groove, adjust the screw so that the bottle inlet side of the screw is close to the bottle without shifting. Adjust the Labeling machine outgoing star wheel just to lift the press head, and adjust the star wheel so that the bottle is in the middle of the star wheel groove.
Labeling machine squeegee and rubber roller adjustment, there should be no gap between the Labeling machine squeegee and rubber roller over the entire length. If there is a gap, the suction steak can be adjusted by adjusting the eccentric bolt. adjustment of Labeling machine rubber roller and standard plate, Labeling machine standard plate and rubber roller is only in contact with each other without any pressure. If the gap is too large, there is too much glue on the target plate, which causes the glue to come off. If the gap is too small and the contact is too tight, the glue will be squeezed out and there will be no glue on half of the target board. Practice shows that the gap between the standard plate and the rubber roller is between 0.1mm and 0.2mm. It can be achieved by adjusting the bearing seat on the lower part of the rubber roller of the Labeling machine, and if necessary, adjusting the bearing on the upper part of the rubber roller.
Aman Machinery Co., Ltd. was established in 2007 and is the authorized supplier of Unilever in Bangladesh. Above is the answer about how to maintain the Labeling machine, if you are interested in Labeling machines, you can contact us, our website is www.amanmachinery.com.